DOWNLOAD SAE J516

Finish The external surfaces and threads of all carbon steel parts shall be plated or coated with a suitable material that passes a 72 h salt spray test in accordance with ASTM B Also limited the number of jump sizes and drops. The 4-bolt split flange SAE dash size is the number of sixteenth inch increments in the flange size. All sealing surfaces must be smooth except that annular tool marks up to min maximum, unless specified otherwise, shall be permissible. Added optional inch hex sizes.

Uploader:	Gabei
Date Added:	15 June 2012
File Size:	60.3 Mb
Operating Systems:	Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads:	38173
Price:	Free* [*Free Regsitration Required]

The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of xae user. All sealing surfaces must be smooth except that annular tool marks up to min maximum, unless specified otherwise, shall be permissible.

Metric fitting size 6x 6. The length of full form external thread shall not be shorter than L2 plus one pitch thread. Workmanship Workmanship shall conform to the best commercial practice to produce high-quality fittings.

Male flareless 24 degree cone hose fittings shall be as shown in Figure 5 and in Table 6 for the applicable hoses and sizes. Where external pipe threads are produced by roll threading, the diameter of the unthreaded shank adjacent to shoulder may be reduced to the E2 pitch diameter.

SAE J hydraulic hose fittings types - Knowledge - Yuyao Jiayuan Hydraulic Fitting Factory

Internal fluid passages shall be protected from corrosion during storage. Specifications are given in detail in SAE J On angle fittings, the cross-sectional area at the junction of fluid passages shall not be less than that of the smallest passage.

Female O-ring face seal hose fittings shall be as shown in Figures 8 to 8B for the respective styles, and Tables 9 to 9B for the applicable hoses and sizes. Unless otherwise indicated, the latest revision of SAE publications shall apply. Where external threads are produced by roll threading and the body is not undercut, the unthreaded portion adjacent to the shoulder may be reduced to the minimum pitch diameter. All internal fluid passages. Parts manufactured to this standard after July 1,shall not be hexavalent chromate coated.

Method of attachment of hose fitting wae hose is optional.

SAE J h516 gives general and dimensional specifications for the most common hose fittings used in conjunction with hydraulic hoses specified in SAE J and used in hydraulic systems on mobile and stationary equipment. Coupling installation and maintenance How to lubricate and maintain the coupling How to use the coupling safely Common problems with couplings Basic information about hydraulics Basic information about the connector Reason for use of the connector The basic meaning of the connector ISO 1 2 3 4 5 6 standards pdf version O-ring face seal hose fittings design 24 degree cone Metric hose fittings Types Four blot split flange hose fittings types Metric stud o-ring hose fittings types JIC 37 degree flare saf fittings types BSPP 60 degree Cone hose fittings types ISO Standard Pdf Specification ISO Pdf standard Specification Download ISO 48 1 2 3 4 5 6 7 8 9 Standard chart.

Female 45 degree flare hose fittings shall be as shown by the 37 degree figures and tables.

Hose Fitting Connector Identification 3. Where passages in straight fittings are machined from opposite ends, the offset at the meeting point shall not exceed 0.

SAE J516 hydraulic hose fittings types

Female 37 degree flare hose fittings shall be as shown in Figures 4 to 4B for the respective styles and shapes, and in Tables 5 to 5B for the applicable hoses and sizes. An R symbol to the left of the document title indicates a complete revision of the report.

SAE invites your written comments and suggestions. The O-ring boss, 37 degree and 45 degree flared, and flareless type thread SAE dash sizes correspond to the number of sixteenth inch increments in the outside diameter of the tubing with which they are designed to be used.

Coupling selection skills How to use the coupling in a special working en Additional permanent marking is also required to provide a means to idenitfy the proper hose to be used with the hose fitting.

The pitch diameter tolerance shall be the same as the corresponding diameter-pitch combination and class of the Unified Fine and 12 thread series. Finish The external surfaces and threads of all carbon steel parts shall be plated or coated with a suitable material that passes a 72 h salt spray test in accordance with ASTM B Government Printing Office, Mail Stop: For externally threaded parts with additive finish, the maximum diameters of Class 2A may be exceeded by the amount of the allowance, that is, the basic diameters Class 2A maximum diameters plus the allowance shall apply to an externally threaded part after plating.

SAE J516 Hose Fittings

Refer to SAE J for specifications of hose and information on hose assemblies. Straight Threads Unified Standard Class 2A external and Class 2B internal threads shall apply to plain finish unplated fittings having straight threads designated B. Added the idenification information Paragraph 4.

All hose fittings, permanently attached and field attachable styles, shall be legibly and permanently marked with the manufacturers name or logo to allow for positive identification.

Parts intended for commercial and industrial use shall not be cadmium plated. Flange connectors for use at pressures of 3.